Indoor/Outdoor 4 station Wireless Thermometer

This simple digital wireless thermometer is great both indoors and out! With up to 3 remote sensors, it can be used to monitor your hot tub and/or swimming pool,  as well as your greenhouse, barn, garage, RV, wine cellar, aquarium, outside temperature, or anything else you can think of. The wireless remote sensors each have their own temperature display, and transmit the temperature to the main station display up to 75 feet away.

The remote sensors can be used with or without the included probe. For spa use the remote unit can be mounted on a wall with the probe going into the spa water or put the remote in the equipment area and tape the probe onto one of the plumbing pipes (the remote sensor is waterproof but only the probe should be submersed). High and low alarm settings can be programmed to alert you if your spa water temperature is too high or too low. The main station will sound an alarm if the temperature rises above or below the min/max settings.

Up to three remote sensors can be used with the main unit to monitor several remote areas. The main station display shows room temperature, and the temperature for up to 3 remote sensors. It can be set for centigrade or farenheight, has a low battery indicator for both itself and the remote sensors, is very easy to program and  comes with one remote sensor (additional remotes sold separately).

Instructions

Simple Set up Instructions Remote Sensor:

1. Remove the stand clip from the four corners on back of unit.
2. Insert 3 AAA Alkaline or Lithium batteries in remote sensor by removing the four screws on back of unit (The stand clip must be removed)
3. LCD display will show all segments for 3 seconds
4. Attach remote probe if required for application.
5. Sensor will automatically link to:: Main Station when Main Station is activated.
6. Press the C/F button to toggle between Centigrade and Fahrenheit.

Specifications:

Main Station Temperature Range -40F to 392F(-40Cto200C)

LLL Indicates reading less than -40F(-40C)
HHH indicates reading more than 392F(20QC)
Display resolution 1 degree C/F

Main Station indoor temperature

Sampling, every 3 seconds.
Temperature range 32F to 122F(OC - 122C)
LLL indicates reading less than 32F(0C)
HHH indicates reading higher than 122F (50C)

Battery Life - 6 months depending on use.

Low Battery Indicators - if remote sensor batteries or main station batteries are low an icon will be present on main station Caution: Do not mix alkaline batteries with Cadmium or Lithium batteries.

Note: The temperature displayed is taken from the interior sensor unless probe is used When the probe is used the temperature displayed is from the probe itself.

Simple Set up Instructions Main Station:

1. Insert two AAA Alkaline or Lithium batteries into main station battery compartments
2. LCD display will show all segments for 3 seconds, then beeps and goes into receiving mode for 1 minute.
3. Main Station automatically links remote transmitters. You may wish to indicate which channel is being used on the back of that particular sensor.

Operating Instructions Main Station:

1. Normal operation - The Main Station automatically links up to three remote transmitters. If more than one sensor is being used the next higher channel is automatically selected. If all three channels are in use, the main station will automatically replace Channel 1.
2. CIF button - on back of unit is used to toggle between Centigrade and Fahrenheit.
3. Hi/Low Button - pressing the Hi/Low button on back will toggle between higher than and lower than temperature set points This is indicated by arrows on the LCD screen.
4. Channel Button - on back will change channel display when multiple sensors are used. Channel Auto Scroll feature is enabled by holding the Channel button down for 2 seconds. The remote temperature display will then display each remote sensor for 2 seconds.
5. Hi/Low Button & Channel Button - when pressed together it allows toggling between indoor temperature display or set temperature display.
6. Set Button - on front is used to set remote temperature alarms. Depressing the set button will allow a toggle between channels when multiple sensors are in use.
7. Up arrow - pressing the up arrow on front is used in set mode and will increase the set temperature 1 degree. Holding down the up arrow for 1 second will make the set point increase at 10 degrees per second.
8. Alarm Set Point Reached - When more than one remote alarm set point is reached the left most display will be overwritten with the temperature of   the remote sensor temperature that has reached its set point.
9. Alarm -The Alarm will sound when the set temperature is reached until;

A. Any front key is pressed (Set or Up arrow)
B The Alarm Times Out after 1 minute

Return to Thermometers , Store Directory

Store Directory | Home Page